Works in Progress: Mansion's Library Ceiling

I love ceilings (and chandeliers). Sounds weird, but I am a weird person so it makes sense. I wanted my 2 story library to have a drop dead gorgeous ceiling -- not as impressive as I want the dining room and ballroom's ceilings to be, but still eye catching!

I found the resin coffer ceilings by Lawbre and ordered a small army of them. Disappointed when they arrived to discover that they are not perfect squares. So much for my plan to just lay them down side by side across the ceiling...

The square on the left is slightly smaller and lower than the one on the right.

They were also not the same depth as some had corners that were raised higher than others. And I would have to cut them right down the middle to fit in my ceiling flush left to right. What tool would I use to cut resin? Plus, that many little squares across my ceiling would look very busy. Ugh. I needed more coffee for this project!

After a few moments (and a few sips of coffee) I thought of a solution that would obliterate the headache of imperfect sizes and busy square pattern! Spread the squares out and insert filler strips of wood! Without being right up next to each other, the difference of sizes wouldn't be as noticeable and it would help reduce the busy pattern to just be an intricate design!

Added wood strips to space squares apart.

Still had a little bit of uneven edges and dips to work out so a layer of wall plaster went on to even everything out....

Spreading the plaster over the wood and between the squares.

Waiting for plaster to dry so that I may sand.

Plaster all dry and it fits in the house! Crown molding will cover the gaps at the edges.

But I hate sanding and it seemed like every time I sanded one spot, fine cracks or marks would appear in another spot. I did not like the imperfections I kept seeing up close:

The imperfections in the plaster seemed to be everywhere.

Fine hairline cracks, dents and dips, and small holes were driving me crazy -- not that I had far to drive to get there! LOL So, time to wallpaper! Using wallpaper liner (I love that stuff!) I papered over the ceiling and used an Exacto knife to cut out the spaces where my ceiling square medallions were located.

All smooth and no more hairline cracks everywhere!

Much better!

So now I was pleased with that aspect of the ceiling. But it is supposed to be elegant. It needs gold and color. But not too much because the wallpaper in the library is gold with red/burgundy and teal accents. So the ceiling only needs a touch of gold:

Lower right square is getting gold trim strip wood cut.

I added a little bit of gold paint to the detailing in the Lawbre squares. And then outlined them in gold painted double bead strip wood.

All white and gold!

I love bright, bold, dark, and/or intense colors. And although white and gold has it's place, I wanted more on the ceiling. So I found a wallpaper that had colors which coordinated with the gold wallpaper going on the walls and put it behind the ceiling so there would be a pop of color:

Ready to be glued into the house!

So ceiling is done, ready to be glued into the house, complete with holes for the micro-jacks for the chandelier! Wait, what? You don't know what micro-jacks are?!?!? They are my newly found answer to my prayers for ceiling light installation!

Created by Creative Reproductions 2 Scale micro-jacks are small eyelet type pieces you install into the ceiling that, along with an adapter, allows you to plug any chandelier in to the ceiling. They are similar to the spring loaded eyelets, but are easier to install and have little teeth around the edges to allow them to better grip and hold where you are installing them. They make the chandelier easily removable allowing for quicker bulb replacement, smoother transport of the dollhouse as delicate chandeliers can be removed, and/or the ability to swap chandeliers around in the house (so when I decide this chandelier would look better in a bedroom and want to trade it with a ballroom chandelier instead - I just move it!).

There are 2 versions of the micro-jacks: one with tails and one without. The micro-jack without tails just inserts into tapewire (I will be using those in the music room). For the library I am doing round wire so I am soldering the wires to the micro-jack with tails.

The wire wraps around the tail and a spot of solder holds it in place. Then I feed the wire through the hole and lightly hammer the micro-jack into the ceiling.

I am not an expert solder wizard yet so in a low self confidence moment I emailed photos of my micro-jacks to the maker and begged him to review my photos to make sure I did it right. I'm not installing these into my precious ceiling to then discover I did it wrong and have to remove them without marring my ceiling! Luckily Creative Reproductions 2 Scale emailed me back within 12 hours to tell me it looked fine, but that to remember it only takes a touch of solder to make the connection so keep the solder and wire wrapped around the tail to the same diameter as the head of the micro-jack or it won't fit thru my 1/16" hole in my ceiling. So I had to go back and remove some of the solder around the tail of my red wire:

Solder at bottom of tail seems to be slightly larger than head of micro-jack.

These things are small!

So, once I removed the extra solder from my wire, I threaded the wire thru my holes in the ceiling and lightly hammered the micro-jacks into the ceiling!